Motogadget digital control box mo.unit blue

The new mo.unit blue has been further developed and significantly improved compared to the proven previous version. It now has 12 inputs and 10 outputs, exchangeable quality cable clamps and, above all, Bluetooth® LE. This allows the mo.unit blue to be connected directly to our mo.ride app on your smartphone. This functionality is unique in the area of ​​motorcycle accessories.

The entire setup and the alarm system can be controlled via the mo.ride app. Error diagnosis is also possible during operation and without removing the mo.unit. A secure, encrypted keyless go function can also be used.

When activated, simply bringing your smartphone close to the vehicle is enough to get the vehicle ready to start. This means that the on-board power can be switched on by pressing the start button. Pressing it again then starts the engine. Once switched on, the on-board power system remains safely activated while driving, even without a phone.

The mo.unit blue is the digital control unit for a motorcycle, the heart of the entire vehicle's electrics. It can be operated with push-button controls or with conventional, switching handlebar controls. It switches all the necessary components on the vehicle and at the same time takes over the tasks of the electrical fuses.

Relays and individual components in the wiring harness are greatly reduced and new, minimized wiring of the vehicle can be carried out in a very short time.

When using the mo.button, the number of all switchgear connections is reduced to a single cable.


Functions WITHOUT smartphone and mo.ride app:
• Complete digital button control, 4-button or 5-button operation possible
• Complete replacement for the fuse box. 10 independent circuits are digitally monitored and switched off in the event of a fault. Once the fault has been eliminated, the fuse function is automatically reset
• Integrated, location-independent alarm system
• Integrated, digital, load-independent flasher relay, automatic switch-off optional and adjustable, mo.wave mode selectable
• Integrated hazard warning lights
• Indicators can optionally be set as position lights
• Integrated parking light and headlight flasher
• Control of low and high beam (up to 200 W switching capacity) with just one button
• Integrated, digital brake light modulator, flashing mode programmable
• Acceleration-controlled emergency brake light (automatic warning signal)
• Integrated starter relay for starters with magnetic switches (up to 30 A switching capacity)
• Intelligent and configurable control/shutdown of consumers in order to use the maximum starting energy of the battery during the starting process
• Integrated digital horn relay
• Two configurable additional outputs AUX1 and AUX2
• Diagnostic function for assignment of input, output, switching status of the circuit, short circuit diagnosis, etc.
• Calibration and current measurement enables defect detection of all lamps

Functions WITH smartphone and mo.ride app:
• Encrypted connection via Bluetooth® LE (Low Energy), thus tamper-proof
• extremely low power consumption of smartphone and mo.unit blue (0.9mA with Bluetooth active and in power save mode after 6 weeks of inactivity: 0.3mA)
• Keyless-Go (ready to start the vehicle by approaching it with your own smartphone)
• Highly sensitive acceleration sensor enables your driving activity to be displayed in mo.ride using an activity factor, number of curves, top speed, etc.
• Transmission of Alarmo events (with date, time, vehicle on the ground, etc.) to the app
• Setting the mode and sensitivity of the alarm system
• Monitoring the current battery voltage in the app
• Diagnosis of all inputs and outputs, measurement of currents, voltage, device temperature
• Defect detection of all lamps through calibration. If the indicators are defective, the flashing frequency is doubled, a status message is sent in the app and an audio notification is sent by Rideassist.
• Rideassist: optional indicator sound and error messages in real time as audio output via helmet headset.
• Manual switching of outputs via smartphone (except starter)
• Firmware updates without removal at any location via smartphone and app
• Configuration of the setup menu without removal at any location via smartphone and app
• Vehicle management with automatic notifications about maintenance tasks, condition of tires, chain, brake pads, oils, operating fluids, spark plugs, etc. by comparing the vehicle mileage using the speedometer signal
• Logbook records trips and stores all generated vehicle messages, alarm events and maintenance tasks
• Display of parking position and ping! to help with vehicle search
• LIN bus connection available for later connection of suitable motogadget products


Technical requirements:
iPhone from iOS 10 / Android from 8.0 (compatibility may be limited depending on the manufacturer).
Further information about the app is available at mo.ride.de or in Google Play and iTunes.


Scope of delivery:
• mo.unit blue
• 1 x M5 stainless steel screw
• 2 x M5 stainless steel screw with nut
• 1 x speedometer sensor with 2 magnets
• Detailed installation and operating instructions

Matching positive cable (NOT INCLUDED!): 362-001 or 362-002

Specifications and features:
L/W/H: 101 x 61 x 28 mm
Weight: approx. 180 g
Fastening: 2 x M5 stainless steel screws (mounting and ground connection), 1 x M5 screw contact for battery plus
Operating voltage: 6 V - 20 V
Operating temperature: -20°... +80°C

Inputs:
1 x input (+12V switched) for ignition lock or mo.lock
11 x control input (minus/ground switched) for:
• Left blinker
• Right blinker
• Low/high beam
• Starter
• Horn
• Brake light
• Kill switch
• Stand switch
• LIN bus
• AUX1
• AUX2

Outputs:
10 x output (+12V) for:
• Left blinker
• Right blinker
• Dimmed headlights
• High beam
• Starter
• Horn
• Brake light
• Ignition
• AUX1
• AUX2